插装式液控能源选择阀的设计与分析

针对液压系统油源的安全性及可靠性问题，提出油源冗余设计方法，即多油源供给多负载，当某一油源发生故障时能源选择阀切断故障油源，由其他油源给负载提供基本液压能源，系统能完成必须的服役性能。针对液压系统能源选择阀存在的频繁换向与振动问题，提出一种插装式液控能源选择阀，其先导阀采用锥阀和可变阻尼形式，主阀采用三台肩且终端有缓冲功能的滑阀。建立了插装式液控能源选择阀的数学模型，分析了能源选择阀在两种模拟故障下的切换压力及切换时间、油源压力脉动等特性。理论分析结果表明，油源压力阶跃和线性变化时，某能源选择阀切换时间分别为5 ms和7 ms。当压力发生波动时，主阀不会发生振动，还可通过液控先导阀结构设计来控制切换压力和回复压力大小。     

Estimating the spin axis orientation of the Echostar-2 box-wing geosynchronous satellite

For the first time, the spin axis orientation of an inactive box-wing geosynchronous satellite has been estimated from ground-based optical photometric observations of Echostar-2’s specular reflections. Recent photometric light curves obtained of Echostar-2 over four years suggest that unusually bright and brief specular reflections were occurring twice within an observed spin period. These bright and brief specular reflections suggested two satellite surfaces with surface normals separated by approximately 180°. The geometry between the satellite, the Sun, and the observing location at the time of each of the brightest observed reflections, was used to estimate Echostar-2’s equatorial spin axis orientation coordinates. When considering prograde and retrograde rotation, Echostar-2’s spin axis orientation was estimated to have been located within 30° of either equatorial coordinate pole. Echostar-2’s spin axis was observed to have moved approximately 180° in right ascension, within a time span of six months, suggesting a roughly one year spin axis precession period about the satellite’s angular momentum vector.     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

过氧化氢/紫外线/臭氧氧化技术处理肼类污水的应用

采用放大试验规模（处理量1 m³/h）的H₂O₂（过氧化氢）/UV（紫外线）/O₃（臭氧）氧化技术处理肼类推进剂污水，在30.0±1.6 ℃，pH=9.0±0.2的条件下，研究肼类的过氧化氢增强光解臭氧化降解。对比不同氧化技术的协同效应以及对污水降解的影响，重点考察过氧化氢、紫外线、臭氧和初始浓度等工艺参数对降解效果的影响，对氧化技术的应用进行了优化。研究结果表明：该技术可使COD去除率提高27.66%，肼类的降解速率随着过氧化氢投加量、紫外线辐射强度、O₃投加速率和水质地提高而升高，随着初始质量浓度的提高而下降。在最佳工艺下，处理5 000 mg/L质量浓度的废水，处理60 min时，COD去除率分别为98.62%（偏二甲肼）、99.17%（甲基肼）、99.94%（肼）和93.25%（单推-3）。     

双模块下颌式内转进气道/圆锥前体一体化布局研究

为实现三维内转进气道的内收缩流场与圆锥前体的外压缩流场的良好匹配，提出了一种双模块下颌式内转进气道/圆锥前体(Double-modules Chin Inward-turning Inlet and Conical Forebody，DCII/CF)一体化设计方法，获得一种新颖的双发并置、侧向安装的DCII/CF一体化布局。针对该布局形式，开展了DCII/CF一体化构型与传统的单模块内转进气道/圆锥前体(Single-module Inward-turning Inlet and Conical Forebody，SII/CF)一体化构型的数值对比研究。结果表明：DCII/CF一体化布局不仅为内转进气道提供了优秀的前体附面层排移效果，还有效避免了传统SII/CF布局中前体附面层与进气道内部流场之间的相互干扰。在Ma∞=6.0设计状态，DCII/CF一体化布局的进气道总压恢复系数相较传统的SII/CF布局有了显著提高，从0.403提高至0.482；但由于前体附面层的排移，该布局的捕获流量略有降低， SII/CF的流量系数为0.956，该布局则为0.917。而在非设计状态，该布局形式同样具备较好的总压恢复性能，在Ma∞=5.0与Ma∞=4.0的总压恢复系数分别达到了0.586和0.682，明显高于SII/CF的总压恢复系数0.507和0.619。     

弹道交班自适应算法研究

为实现复合制导不同制导弹道的平滑过渡,用二阶吻合法设计了一不同制导律间的指令交接导引段。建立了自适应弹道交接导引算法的模型。理论分析和仿真结果表明,该算法具较好的弹道过载平滑能力,有一定的应用价值。     

在二元柔壁自适应风洞中利用面元法进行三元模型实验

简要叙述了在西北工业大学二元柔壁自适应风洞中利用面元法进行二元半机翼模型试验的研究情况，分析了面元法的基本思想和部分试验结果。     

虚拟环境系统中复杂模型的建立--3D资源在快速开发虚拟环境系统中的应用

对利用3D资源在快速开发虚拟环境系统中的方法进行了研究。在开发虚拟环境系统的过程中，复杂模型的建立是必不可少的，仅仅利用OpenGL函数编程来实现仿真是很困难的，针对该问题提出了利用3D资源进行3D文件读取和转换的两种方案，分析了虚拟环境中复杂模型的建立以及处理的基本方法，并对数控车床的仿真进行了详细介绍。     

一种新型阀瓣结构

在航天器中,一般使用推力器作为姿控、轨控执行元件,推力器中的电磁阀动密封常使用和推进剂相容的橡胶材料.本文介绍一种不用过渡层硫化成型的阀瓣结构,并指出这种结构较目前流行的阀瓣结构所拥有的优越性.     

逆向工程的关键技术及其研究

综述了逆向工程中实物数字化技术、测量数据的预处理、曲面重建技术、重构曲面的评价和检验等关键技术的发展现状和存在的问题,并对今后的发展方向进行了讨论。